View A6150A1X8P_2427052.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 em microelectronic-marin sa a6150 high efficiency linear power supply with power surveillance and software monitoring features ? highly accurate 5 v, 100 ma guaranteed output ? low dropout voltage, typically 380 mv at 100 ma ? low quiescent current, typically 175 a ? standby mode, maximum current 340 a (with 100 a load on output) ? unregulated dc input can withstand ?20 v reverse battery and + 60 v power transients ? fully operational for unregulated dc input voltage up to 26 v and regulated output voltage down to 3.0 v ? reset output guaranteed for regulated output voltage down to 1.2 v ? no reverse output current ? very low temperature coefficient for the regulated output ? current limiting ? comparator for voltage monitoring,voltage reference 1.52 v ? programmable reset voltage monitoring ? programmable power on reset (por ) delay ? watchdog with programmable time windows guarant- ees a minimum time and a maximum time between software clearing of the watchdog ? time base accuracy 10% ? system enable output offers added security ? ttl/cmos compatible ? -40 to +85 c temperature range ? on request extended temperature range,-40 to +125 c ? dip8 and so8 packages description the a6150 offers a high level of integration by combining voltage regulation, voltage monitoring and software monitoring in an 8 lead package. the voltage regulator has a low dropout voltage (typ. 380 mv at 100 ma) and a low quiescent current (175 a). the quiescent current increases only slightly in dropout prolonging battery life. built-in protection includes a positive transient absorber for up to 60 v (load dump) and the ability to survive an unregulated input voltage of ?20 v (reverse battery). the input may be connected to ground or a reverse voltage without reverse current flow from the output to the input. a comparator monitors the voltage applied at the v in input comparing it with an internal 1.52 v reference. the power- on reset function is initialized after v in reaches 1.52 v and takes the reset output inactive after t por depending of external resistance. the reset output goes active low when the v in voltage is less than 1.52 v. the res and en outputs are guaranteed to be in a correct state for a regulated output voltage as low as 1.2 v. the watchdog function monitors software cycle time and execution. if software clears the watchd og too quickly (incorrect cycle time) or too slowly (incorrect execution) it will cause the system to be reset. the system enable output prevents critical control functions being activated until software has successfully cleared the watchdog three times. such a security could be used to prevent motor controls being energized on repeated resets of a faulty system. applications ? automotive systems ? cellular telephones ? security systems ? battery powered products ? high efficiency linear power supplies ? automotive electronics typical operatin g configuration pin assignment 5 v fig. 1 gnd a6150 v in tcl res en r v ss input output unregu- lated voltage version a0: version a1: dip8/ so8 output fig. 2 v in r input a6150 en res tcl v ss
2 a6150 absolute maximum ratings parameter symbol conditions continuous voltage at input to v ss v input -0.3 to + 30 v transients on input for t < 100 ms and duty cycle 1% v trans up to + 60 v reverse supply voltage on input v rev - 20 v max. voltage at any signal pin v max output + 0.3 v min. voltage at any signal pin v min v ss ? 0.3 v storage temperature t sto -65 to + 150 c electrostatic discharge max. to mil-std-883c method 3015 v smax 1000 v max. soldering conditions t smax 250 c x 10 s table 1 stresses above these listed maximum ratings may cause permanent damage to th e device. exposure be- yond specified operating conditions may affect device reliability or cause malfunction. handling procedures this device has built-in protection against high static voltages or electric fields; however, anti-static precau- tions must be taken as for any other cmos component. unless otherwise specified, proper operation can only occur when all terminal voltages are kept within the supply voltage range. at any time, all inputs must be tied to a defined logic voltage level. operating conditions parameter symbol min. typ. max. units operating junction temperature 1) t j -40 +125 c input voltage 2) v input 2.3 26 v output voltage 2) 3) v output 1.2 v res & en guaranteed 4) v output 1.2 v output current 5) i output 100 ma comparator input voltage v in 0v output v rc-oscillator programming r 10 1000 k ? thermal resistance from junction to ambient 6) -dip8 r th(j-a) 105 c/w -so8 r th(j-a) 160 c/w table 2 1) the maximum operating temperature is confirmed by sampling at initial device qu alification. in production, all devices are tested at +85 c. on request devices tested at +125 c can be supplied. 2) full operation quaranteed. to achieve the load regulation specified in table 3 a 22 f capacitor or greater is required on the input, see fig. 18. the 22 f must have an effective resistance 5 ? and a resonant frequency above 500 khz. 3) a 10 f load capacitor and a 100 nf decoupling capacitor are required on the regulator output for stability. the 10 f must have an effective series resistance of 5 ? and a resonant frequency above 500 khz. 4) res and en (en only for version a0) must be pulled up externally to v output even if they are unused. (note: res and en are used as inputs by em test). 5) the output current will not apply for all possible combinations of input voltage and output current. combinations that would require the a6150 to work above the maximum junction temperature (+125 c) must be avoided. 6) the thermal resistance spec ified assumes the package is soldered to a pcb.
3 a6150 electrical characteristics v input = 6.0 v, c l = 10 f + 100 nf, c input = 22 f, t j = -40 to +85 c, unless otherwise specified parameter symbol test conditions min. typ. max. unit supply current in standby mode i ss r ext = don?t care, tcl = v output , v in = 0 v, i l = 100 a 340 a supply current 1) i ss r ext = 100 k ? , i/p s at v output , o/p s 1 m ? to v output , i l = 100 a 175 400 a supply current 1) i ss r ext = 100 k ? , i/p s at v output , v input = 8.0 v, o/p s 1 m ? to v output , i l = 100 ma 1.7 4.2 ma output voltage v output i l = 100 a 4.88 5.12 v output voltage v output 100 a i l 100 ma, -40 c t j +125 c 4.85 5.15 v output voltage temperature coefficient 2) v th(coeff) 50 180 ppm/ c line regulation 3) v line 6 v v input 26 v, i l = 1 ma, t j = +125 c0.20.5% load regulation 3) v l 100 a i l 100 ma 0.2 0.6 % dropout voltage 4) v dropout i l = 100 a 40 170 mv dropout voltage 4) v dropout i l = 100 ma 380 mv dropout voltage 4) v dropout i l = 100 ma, -40 c t j +125 c 650 mv dropout supply current i ss v input = 4.5 v, i l = 100 a, r ext = 100 k ? , o/p s 1 m ? to v output , i/p s at v output 1.2 1.6 ma thermal regulation 5) v thr t j = +25 c, i l = 50 ma, v input = 26 v, t = 10 ms 0.05 0.25 %/w current limit i lmax output tied to v ss 450 ma output noise, 10hz to 100khz v noise 200 vrms res & en output low voltage v ol v output = 4.5 v, i ol = 20 ma 0.4 v v ol v output = 4.5 v, i ol = 8 ma 0.2 0.4 v v ol v output = 2.0 v, i ol = 4 ma 0.2 0.4 v v ol v output = 1.2 v, i ol = 0.5 ma 0.06 0.2 v en (vers. a1) output high voltage v oh v output = 4.5 v, i oh = -1 ma 3.5 4.1 v v oh v output = 2.0 v, i oh = -100 a1.81.9v v oh v output = 1.2 v, i oh = -30 a1.01.1v tcl and v in tcl input low level v il v ss 0.8 v tcl input high level v ih 2.0 v output v leakage current i li v ss v tcl v output 0.05 1 a v in input resistance r vin 100 m ? v ref t j = +25 c 1.474 1.52 1.566 v comparator reference 6)7) v ref 1.436 1.620 v v ref -40 c t j +125 c 1.420 1.620 v comparator hysteresis 7) v hy 2mv table 3 1) if input is connected to v ss , no reverse current will flow from the output to the input, howeve r the supply current specified will be sank by the output to supply the a6150. 2) the output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range. 3) regulation is measured at constant junction temperature using pulse testing with a low duty cycle. changes in output voltage due to heating effects are covered in the specification for thermal regulation. 4) the dropout voltage is defined as the input to output differential, measured with the input voltage equal to 5.0 v. 5) thermal regulation is defined as the change in output voltage at a time t after a change in power dissipation is applied, excluding load or li ne regulation effects. 6) the comparator and the voltage regulator have separate voltage references (see ? block diagram? fig. 7). 7) the comparator reference is the power-down reset threshold. th e power-on reset threshold equals the comparator reference voltage plus the comparator hysteresis (see fig. 4).
4 a6150 timing characteristics v input = 6.0 v, i l = 100 a, c l = 10 f + 100 nf, c input = 22 f, t j = -40 to + 85 c, unless otherwise specified parameter symbol test conditions min. typ. max. units propagation delays: tcl to output pins t dido 250 500 ns v in sensitivity t sen 1520 s logic transition times on all output pins t tr load 10 k ? , 50 pf 30 100 ns power-on reset delay t por r ext = 123 k ? 1% 90 100 110 ms watchdog time t wd r ext = 123 k ? 1% 90 100 110 ms open window percentage owp 0.2 t wd closed window time t cw 0.8 t wd t cw r ext = 123 k ? 1% 72 80 88 ms open window time t ow 0.4 t wd t ow r ext = 123 k ? 1% 36 40 44 ms watchdog reset pulse t wdr t wd /40 t wdr r ext = 123 k ? 1% 2.5 ms t cl input pulse width t tcl 150 ns table 4 timing waveforms watchdog timeout period voltage monitoring t wd = t por t cw ? closed window t ow ? open window watchdog timer reset condition: r ext = 123 k ? ? owp ? 20% + owp + 20% 80 100 120 fig. 3 t [ms] t sen t sen t sen t sen t por t por res v in v ref v hy conditions: v output 3 v no timeout fig. 4
5 a6150 timer reaction combined voltage and timer reaction block diagram t cw +t ow t ow v in v ref tcl res en condition: v output 3 v fig. 6 - watchdog timer reset tcl too early 3 correct tcl service en goes active low 1 2 3 t por =t wd t cw voltage regulator voltage reference voltage reference input v in r output enable logic reset control timer v ref comparator tcl fig. 7 en res current controlled oscillator open drain output res vers. a0 vers. a1 conditions: v in > v ref after power-up sequence t cw t ow t cw t ow t cw t tcl t wdr tcl res en fig.5 1 2 3 - watchdog timer reset t cw +t ow t cw +t ow t cw +t ow 3 correct tcl services timeout en goes active low
6 a6150 pin description pin name function 1en vers. a0: open drain active low enable output. en must be pulled to v output even if unused vers. a1: push-pull active low reset output 2 res open drain active low reset output. res must be pulled up to v output even if unused 3 tcl watchdog timer clear input signal 4v ss gnd terminal 5 input voltage regulator input 6 output voltage regulator output 7r r ext input for rc oscillator tuning 8v in voltage comparator input table 5 functional description voltage regulator the a6150 has a 5 v 2%, 100 ma, low dropout volt- age regulator. the low supply current (typ.155 a) mak- es the a6150 particularly suit ed to automotive systems then remain energized 24 hours a day. the input voltage range is 2.3 v to 26 v for operation and the input protec- tion includes both reverse battery (20 v below ground) and load dump (positive transients up to 60 v). there is no reverse current flow from the output to the input when the input equals v ss . this feature is important for systems which need to implement (with capacitance) a minimum power supply hold-up time in the event of power failure. to achieve good load regulation a 22 f capacitor (or greater ) is needed on the input (see fig. 18). tantalum or aluminium el ectrolytics are adequate for the 22 f capacitor; film types will work but are relati- vely expensive. many aluminium electrolytics have electrolytes that freeze at about ?30 c, so tantalums are recommended for operation below ?25 c. the impor- tant parameters of the 22 f capacitor are an effective series resistance of 5 ? and a resonant frequency above 500 khz. a 10 f capacitor (or greater) and a 100 nf capacitor are required on the output to prevent oscillations due to instability. the specification of the 10 f capacitor is as per the 22 f capacitor on the input (see previous paragraph). the a6150 will remain stable and in regulation with no external load and the dropout voltage is typically con- stant as the input voltage fall to below its minimum level (see table 2). these features are especially important in cmos ram keep-alive applications. care must be taken not to exceed the maximum junction temperature (+ 125 c). the power dissipation within the a 6150 is given by the formula: p total = (v input ? v output ) * i output + (v input ) * i ss the maximum continuous powe r dissipation at a given temperature can be calculated using the formula: p max = ( 125 c ? t a ) / r th(j-a) where r th(j-a) is the termal resistance from the junction to the ambient and is specified in table 2. note the r th(j-a) given in table 2 assumes th at the package is soldered to a pcb. the above formula for maximum power dissi- pation assumes a constant load (ie. 100 s). the transient thermal resistance for a single pulse is much lower than the continuous value. for example the a6150 in dip8 package will have an effective thermal resistance from the junction to the ambient of about 10 c/w for a single 100 ms pulse. v in monitoring the power-on reset and th e power-down reset are generated as a response to the external voltage level applied on the v in input. the v dd voltage at which reset is asserted or released is determined by the external voltage divider between v dd and v ss, as shown on fig. 18. a part of v dd is compared to the internal voltage reference. to determine the values of the divider, the leakage current at v in must be taken into account as well as the current consumption of the divider itself. low resistor values will need mo re current, but high resistor values will make the reset threshold less accurate at high temperature, due to a possible leakage current at the v in input. the sum of the two resistors should stay below 300 k ? . the formula is: v reset = v ref *(1 + r 1 /r 2 ). example: choosing r 1 = 100 k ? and r 2 = 51 k ? will result in a v dd reset threshold of 4.5 v (typ.). at power-up the reset output (res) is held low (see fig. 4). after input reaches 3.36 v (and so output reaches at least 3 v) and v in becomes greater than v ref , the res output is held low for an additional power-on- reset (por) delay which is equal to the watchdog time t wd (typically 100 ms with an external resistor of 123 k ? connected at r pin). the por delay prevents repeated toggling of res even if v in and the input voltage drops out and recovers. the por delay allows the micropro- cessor?s crystal oscillator time to start and stabilize and ensures correct recognition of the reset signal to the microprocessor. the res output goes active low generating the power- down reset whenever v in falls below v ref . the sensiti- vity or reaction time of the internal comparator to the vol- tage level on v in is typically 5 s. timer programming the on-chip oscillator with an external resistor r ext con- nected between the r pin and v ss (see fig. 18) allows the user to adjust the power-on reset (por) delay, watchdog time t wd and with this also the closed and open time windows as well as the watchdog reset pulse width (t wd /40). with r ext = 123 k ? typical values are: -power-on reset delay: t por is 100 ms -watchdog time: t wd is 100 ms
7 a6150 -closed window: t cw is 80 ms -open window: t ow is 40 ms -watchdog reset: t wdr is 2.5 ms note the current consumption increases as the fre- quency increases. watchdog timeout period description the watchdog timeout period is divided into two parts, a ?closed? window and an ?open? window (see fig. 3) and is defined by two parameters, t wd and the open window percentage (owp). the closed window starts just after the watchdog timer resets and is defined by t cw = t wd ? owp(t wd ). the open window starts after the closed time window finishes and lasts till t wd + owp(t wd ).the open window time is defined by t ow = 2 x owp (t wd ) for example if t wd = 100 ms (actual value) and owp = 20% this means the closed window lasts during first the 80 ms (t cw = 80 ms = 100ms ? 0.2 (100 ms)) and the open window the next 40 ms (t ow = 2 x 0.2 (100 ms) = 40 ms). the watchdog can be serviced between 80 ms and 120 ms after the timer reset. however as the time base is 10% accurate, software must use the following calculation as the limits for servicing signal tcl during the open window: related to curves (fig. 10 to fig. 20), especially fig. 19 and fig. 20, the relation between t wd and r ext could easily be defined. let us ta ke an example describing the variations due to production and temperature: 1.choice, t wd = 26 ms. 2.related to fig. 20, the coefficient (t wd to r ext ) is 1.155 where r ext is in k ? and t wd in ms. 3.r ext (typ.) = 26 x 1.155 = 30.0 k ? . 4. 26 ms at +25 c a) (26 ? 10% = 23.4 ms) (26 + 10% = 28.6 ms) a) b) (23.4 ? 5% = 22.2 ms) (28.6 + 5% = 30.0 ms) b) min.: (30.0 ? 20% = 24.0 ms) max.: (22.2 + 20% = 26.7 ms) typical tcl period of (24.0 + 26.7) / 2 = 25.4 ms the ratio between t wd = 26 ms and the (tcl period) = 25.4 ms is 0.975. then the relation over the production and the full temperature range is, tcl period = 0.975 x t wd or tcl period = , as typical value. a) while production value unknown for the custo- mer when r ext 123 k ? . b) while operating temperature range -40 c t j +85 c. 5. if you fixed a tcl period = 26 ms ? r ext = = 30.8 k ? . if during your production the t wd time can be mea- sured at t j = + 25 c and the c can adjust the tcl period, then the tcl period range will be much larger for the full operating temperature. t wd versus v output at t j = +25 c t wd versus r at t j = +25 c 1 0 ? 000 1000 1 00 1 0 1 3 4 5 v output [v] fi g . 8 t wd [ms] 6 r = 10 m ? ? r = 100 k ? r = 10 k ? ? 0.1 1 10 100 1000 10?000 1 10 100 1000 10?000 t wd [ms] r[k ? ] fig. 9 3 v 4.8 v 5 v 5.2 v 6 v 0.975 x r ext 1.1 55 26 x 1.155 0 . 9 7 5
8 a6150 t wd versus r at t j = +25 c 1 10 100 1000 t wd [ms] 0 .1 1 10 100 1000 10?000 r[k ? ] fig. 10 3 v 4.8 v 5 v 5.2 v 6 v 10?000
9 a6150 t wd versus v output at t j = +85 c t wd versus r at t j = +85 c t wd versus v output at t j = -40 c t wd versus r at t j = -40 c fig. 12 0.1 10 100 1000 10?000 1 10 100 1000 10?000 t wd [ms] r[k ? ] 1 3 v 4.8 v 5 v 5.2 v 6 v 10?000 1000 100 10 1 3 4 5 v output [v] fig. 11 t wd [ms] 6 r = 10 m ? r = 1 m ? r = 100 k ? r = 10 k ? r = 1 k ? 10?000 1000 100 10 1 3 4 5 v output [v] fig. 13 t wd [ms] 6 r = 10 m ? r = 1 m ? r = 100 k ? r = 10 k ? r = 1 k ? 0.1 10 100 1000 10?000 1 10 100 1000 1 r[k ? ] 0.1 t wd [ms] fig. 14 3 v 4.8 v 5 v 5.2 v 6 v
10 a6150 t wd versus temperature at 5 v t wd versus r at 5 v output current versus input voltage 10?000 1000 100 10 1 -40 0 +40 t j [ c] fig. 15 t wd [ms] +80 r = 10 m ? -20 +20 +60 r = 1 m ? r = 100 k ? r = 10 k ? r = 1 k ? 0.1 10 100 1000 10?000 1 10 100 1000 10?000 t wd [ms] r[k ? ] fig. 16 1 -40 c -20 c +25 c +70 c +85 c 0 5 10 15 20 25 30 input voltage [v] fig.17 20 0 40 60 80 1 00 output current[ma] t a =+50 c t a =+85 c t a =+25 c so8 package soldered to pc board t jmax = + 125 c
11 a6150 timer clearing and res action the watchdog circuit monitore the activity of the proces- sor. if the user?s software does not send a pulse to the tcl input within the programmed open window timeout period a short watchdog res pulse is generated which is equal to t wd /40 = 2.5 ms typically (see fig. 5). with the open window constraint new security is added to conventional watchdogs by monitoring both software cycle time and execution. should software clear the watchdog too quickly (incorrect cycle time) or too slowly (incorrect execution) it will cause the system to be reset. if software is stuck in a loop which includes the routine to clear the watchdog then a conventional watchdog would not make a system reset even though software is malfunctioning; the a6150 would make a system reset because the watchdog would be cleared too quickly. if no tcl signal is applied before the closed and open windows expire, res will start to generate square waves of period (t cw + t ow + t wdr ). the watchdog will remain in this state until the next tcl falling edge appears during an open window, or until a fresh power-up se- quence. the system enable output, en , can be used to prevent critical control functions being activated in the event of the system going into this failure mode (see section ?enable-en output?). the res output must be pulled up to v output even if the output is not used by the system (see fig 18). combined voltage and timer action the combination of voltage an d timer actions is illustrat- ed by the sequence of events shown in fig. 6. on pow- er-up, when the voltage at v in reaches v ref , the power- on-reset, por, delay is initialized and holds res active for the time of the por delay. a tcl pulse will have no effect until this power-on-res et delay is completed. when the risk exists that tcl temporarily floats, e.g. during t por , a pull-up to v dd is required on that pin. after the por delay has elapsed, res goes inactive and the watchdog timer starts acting. if no tcl pulse occurs, res goes active low for a short time t wdr after each closed and open window period. a tcl pulse coming during the open window clears the watchdog timer. when the tcl pulse occurs too early (during the closed window), res goes active and a new timeout sequence starts. a voltage drop below the v ref level for longer than typically 5 s overrides the timer and immediately forces res active and en inactive. any further tcl pulse has no effect until the next power-up sequence has completed. enable - en output the system enable output, en ,is inactive always when res is active and remains inactive after a res pulse until the watchdog is serviced correctly 3 consecutive times (ie. the tcl pulse must come in the open win- dow). after three consecutive services of the watchdog with tcl during the open window, the en goes active low. a malfunctioning system would be repeatedly reset by the watchdog. in a conventional system critical motor controls could be energized each time reset goes inac- tive (time allowed for the system to restart) and in this way the electrical motors driven by the system could function out of control. the a6150 prevents the above failure mode by using the en output to disable the motor controls until software has successfully cleared the watchdog three times (ie. the system has correctly re- started after a reset condition). for the version a0 the en output must be pulled up to v output even if the output is not used by the system (see fig. 18. typical application input output a6150 r v ss 22 f + + regulated voltage fig.18 unregulated voltage gnd 100 k ? 100 nf 10
12 a6150 t wd coefficient versus r ext at t j = + 25 c r ext coefficient versus t wd at t j = + 25 c 0.96 0.94 0.92 0.90 0.88 0.86 0.84 0.82 0.80 0.78 0.76 t wd coefficient 10 1000 100 r ext [ k ? ] fig. 19 fig. 20 1.30 1.28 1.26 1.24 1.22 1.20 1.18 1.16 1.14 1.12 1.10 1.08 1.06 1.04 r ext coefficient 10 100 1000 t wd [ms]
13 a6150 package information dimensions of 8-pin soic package min nom max a 1.35 1.63 1.75 a1 0.10 0.15 0.25 b 0.33 0.41 0.51 c 0.19 0.20 0.25 d 4.80 4.93 5.00 e 3.80 3.94 4.00 e 1.27 h 5.80 5.99 6.20 l 0.40 0.64 1.27 2 3 4 5 6 7 8 h l 0 - 8 c e a 1 a b e d dimensions in mm fig. 21 dimensions of 8-pin plastic dip package a 1 a 2 a l e b2 eb ea c b3 b e dimensions in mm 1 2 3 4 5 6 7 8 min. nom. max. min. nom. max. a 5.33 d 9.01 9.27 10.16 a1 0.38 e 7.62 7.87 8.25 a2 2.92 3.30 4.95 e1 6.09 6.35 7.11 b 0.35 0.45 0.56 e 2.54 b2 1.14 1.52 1.78 ea 7.62 b3 0.76 0.99 1.14 eb 10.92 c 0.20 0.25 0.35 l 2.92 3.30 3.81 e1 fig.22
14 a6150 ordering information when ordering, please specify complete part number part number output en temperature rang e package delivery form package marking (first line) a6150a1so8a 8-pin soic stick 6150a1 a6150a1so8b push-pull 8-pin soic tape & reel 6150a1 a6150a1dl8a* -40 c to +85 c 8-pin plastic dip stick a6150a1 a6150a0so8a* 8-pin soic stick 6150a0 a6150a0so8b* open drain 8-pin soic tape & reel 6150a0 a6150a0dl8a* 8-pin plastic dip stick a6150a0 a6150a1xso8a* 8-pin soic stick 6150a1x a6150a1xso8b* push-pull 8-pin soic tape & reel 6150a1x a6150a1xdl8a* -40 c to +125 c 8-pin plastic dip stick a61501x a6150a0xso8a* 8-pin soic stick 6150a0x a6150a0xso8b* open drain 8-pin soic tape & reel 6150a0x a6150a0xdl8a* 8-pin plastic dip stick a61500x * = non stock item. might be available on request and upon minimum order quantity (please contact em microelectronic). em microelectronic-marin sa cannot assume any responsibility for use of any circuitry described other than entirely embodied in an em microelectronic-mari n sa product. em microelectronic-marin sa reserves the right to change the circuitry and specifications without notice at any time. you are strongly urged to ensure that the information given has not been superseded by a more up-to-date version. ? 2002 em microelectronic-marin sa , 03/02 , rev. n/344 em microelectronic-marin sa , ch - 2074 marin , switzerland , tel. +41 ? ( 0 ) 32 75 55 111 , fax +41 ? ( 0 ) 32 75 55 403

▲Up To Search▲

Price & Availability of A6150A1X8P

	To Download A6150A1X8P Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .